What a sump pump service visit should check, from the power supply and float switch to the check valve, discharge line and alarm, and which parts of the job belong to a licensed pump contractor.

Last updated: November 2026

A sump pump maintenance checklist should cover the power supply, the pit, the float switch, a full test cycle, the check valve, the discharge line and the alarm. Zoeller, a sump pump manufacturer, tells owners to inspect and test the system at least every three months. A backup pump, if you have one, belongs on the same list.

This guide is for San Diego County homeowners and property managers whose pump sits in a crawlspace, under a slab or in a below-grade room. Most homes here have a crawlspace or slab, not a basement. So the pit is usually out of sight, and nobody thinks about it until the alarm goes off.

What should a sump pump maintenance checklist cover?

A sump pump maintenance visit should check every part that can stop water from leaving the pit. The motor is only one of them. The list below follows the installation and care instructions Zoeller publishes for its sump pumps. Use it to judge what a service visit covered. It isn’t a do-it-yourself procedure.

  1. Power is shut off at the breaker and the pump is unplugged before anyone handles it. Zoeller gives that order before any servicing.
  2. The pump runs on its own separately protected, properly grounded circuit. Nothing is plugged in through an extension cord, which Zoeller says never to use with a sump pump.
  3. The power cord has no cuts, splices or damage. The instructions say never to cut or splice the cord outside a watertight junction box.
  4. Debris is cleaned out of the pit. A pump sitting on sand, gravel or dirt gets a proper base, since Zoeller says not to install on those.
  5. The float switch moves freely. The float switch is the part that rises with the water and tells the pump when to start and stop. Zoeller lists debris under the float, or a float bound by the pit sides, as causes of pump failure.
  6. The pump is run through a full cycle. It should start at the right water level, empty the pit and shut off cleanly.
  7. The check valve holds. A check valve is a one-way valve in the discharge line that keeps pumped water from running back into the pit. The instructions call for a check valve and a union in the discharge line, and a vent hole that stays clear when a check valve is used.
  8. The discharge line is clear, and it is no smaller than the pump’s discharge opening.
  9. The high-water alarm sounds when it’s tested.
  10. Any backup pump gets tested too. Where a primary pump failure could cause damage, Zoeller suggests considering a two-pump system with an alarm, or a DC backup system.
  11. You hear about any wear found during the visit, so a repair or replacement doesn’t come as a surprise later.

If a visit skipped the float, the check valve or the alarm, it skipped the parts that fail quietly.

How often should a sump pump be inspected?

Zoeller’s instructions say to inspect and test a sump pump system at least every three months. That’s one manufacturer’s minimum for its own pumps. Other brands publish their own schedules, so check the manual for the pump you have before settling on a number.

A quick look between visits is a much smaller job than a full service visit. The three-month check can be as simple as confirming the pump has power and the alarm works. Cleaning the pit, freeing a float and testing the check valve is hands-on work inside the pit.

How often a property needs that deeper visit depends on the system. A single pump under a house is a different job from a duplex pump station serving a building. That’s why our Planned Maintenance Programs are customized. Each one is designed for the specific application to help prevent premature pump failure and to keep the system running efficiently.

Regular visits also catch problems before they turn into a flooded crawlspace. As we wrote in “Why your sump pump keeps running when it hasn’t rained,” planned maintenance can catch a pump that is cycling abnormally, a control that isn’t behaving correctly, or a discharge issue.

Which warning signs mean the pump needs more than maintenance?

Some sump pump problems go past routine maintenance and call for a repair or a new pump. Our repair page lists the signs worth a call: a pump that is 10 years old or older, a pump running with no water in the pit, a pump clogged with debris, a very loud pump, or one that runs constantly in dry weather.

Wear shows up in other ways too. Visible rust, excessive vibration, long run times and irregular starting and stopping are all signs a pump may be reaching the end. If a technician points out any of these during a maintenance visit, ask whether sump pump repair makes sense or whether the pump is due for replacement. We replace both submersible and pedestal sump pumps.

A maintenance checklist isn’t a diagnosis guide. If your pump has already stopped, check “Sump pump not turning on: what to check before you call.” If it’s making new noises, see “Grinding, humming, gurgling: what each sump pump noise means.” If the alarm is sounding, start with “Your sump pump alarm went off. Now what?”

What can you check yourself, and what needs a licensed pump contractor?

Homeowners can safely look and listen from a dry spot. Everything that involves the pit, the wiring or the plumbing belongs to a licensed pump contractor. Zoeller’s own instructions tell owners not to service or take apart the pump and to contact the factory or an authorized service station instead.

Safe things to do between visits:

  • Stand somewhere dry and listen. A pump that runs and shuts off is normal. One that hums without moving water, or never stops, needs a call.
  • Check that the circuit breaker for the pump hasn’t tripped, and that any control panel or alarm lights look normal.
  • Keep the pit lid on and the area around it clear.
  • Write down when the alarm went off and how long the pump ran. That helps the technician.

Leave these to a pro:

  • Reaching into the pit for any reason.
  • Freeing a stuck float, resetting a switch or touching the wiring.
  • Opening or replacing a check valve or cutting into the discharge line.
  • Anything on a sewage ejector. Never open a sewage basin. Sewage contact is always a job for a licensed contractor with the right equipment, and our sewer ejector pump service covers maintenance and repair on that side.

Pits and sumps are confined spaces. Our technicians are certified in Confined Space Entry, which is the training that work calls for.

What to have ready before a maintenance visit

A maintenance visit goes faster when the technician knows the system’s history.

Know roughly how old the pump is, if you can. Note when the alarm last went off and whether anything changed after a storm. Mention any new sounds, long run times, or water you’ve seen near the pit. Tell us if there’s a backup pump or battery system, and where the electrical panel is.

Clear a path to the pit. In a crawlspace that might mean moving stored items away from the access hatch. Under a slab or in a below-grade room, make sure the pit lid isn’t buried under boxes.

Frequently asked questions

Can I do sump pump maintenance myself?

You can do the visual checks. Look and listen from a dry spot, make sure the breaker hasn’t tripped and confirm the alarm works. Cleaning the pit, freeing a float and testing the check valve mean working inside the pit near water and power. Zoeller tells owners not to service or take apart its pumps. Leave that work to a licensed pump contractor.

Does a sewage ejector pump need the same maintenance as a sump pump?

A sewage ejector needs regular maintenance too, but it is a different system and a different job. A sump pump moves groundwater. A sewage ejector moves waste from below-grade plumbing. Homeowners should never open a sewage basin or reach into it. Maintenance and repair on a sewage ejector belong to a licensed contractor with the right equipment.

Should the power be off before anyone works on a sump pump?

Yes. Zoeller’s instructions say to shut off the main power breaker and then unplug the pump before servicing it. That applies to anyone working on the pump. For homeowners, the safer move is not to reach into the pit at all. If the pump needs hands-on work, call a licensed pump contractor and let them handle the power and the pump.

Is a battery backup pump part of a maintenance visit?

It should be, if you have one. A backup pump that never gets tested may not run when the primary pump fails. Zoeller suggests considering a two-pump system with an alarm, or a DC backup system, where a primary pump failure could cause damage. Ask for the backup to be run during the visit along with the main pump.

Does regular maintenance make a sump pump last longer?

Fox Pump Systems’ view is that routine planned maintenance, done properly, helps prevent pump breakdowns and increases equipment life. A visit can catch a sticking float, a failing check valve or a clogged discharge line before it takes the pump down with it. Maintenance can’t make an old pump new, though. Pumps 10 years old or older are worth a closer look.

How Fox Pump Systems can help

Fox Pump Systems services and replaces sump pumps for homeowners and property managers across San Diego County. Steve Fox has worked on sewage and sump pumps since 1986. Our technicians are certified in Confined Space Entry and First Aid/CPR, and we hold CSLB Lic #928391.

We offer customized Planned Maintenance Programs designed for each specific application. The program also gives you preferred priority customer status when something goes wrong.

If your pump is failing now, call 619-240-4013. Emergency pump service is available 24/7. For a maintenance visit that can wait, send a service request.

Previous Post

Your sump pump alarm went off. Now what?

Next Post

How a sewage ejector pump works and where it's required